Local Reviews
Edwin M.
REFRIGERATOR JENN-AIR JFC2089HTW Unit has failed control cannot properly test unit; ordrng 1 WPW10207861 (cntrl-elec)
Aris S.
D/WASHER UNDCTR WHIRLPOOL WDTA50SAHV0 "Fixed a loose connection by the control board, run it on service diagnostic, is working normal"
Aris S.
RANGE MAYTAG MGR5755QDS "Unit need many parts because the burners cap are rusted, need the main top, all burner, all the tubing, all the screws, for burner, customer will callback if he want to fixed"
Ken K.
REFRIGERATOR WHIRLPOOL WRF560SMYM04 "Replaced defective damper control, due to making noise and main control due to warm temp in RC"
Aris S.
REFRIGERATOR WHIRLPOOL WRS322FDAM04 "Fixed a loose connection by light, test it is working good"
Eric P.
OVEN KITCHENAID KDRS467VSS05 "Ep-unit has slow heating in bake, lights also flash on and off while running. You can hear the relays clicking continuously. unit also has a weld/laser burn on glass cut-out, covered under 30-day cosmetic.Ordering (1) W10852104 cntrl-elec,(1) W10852683 nameplate, (1) WPW10225960 panel-door; ordrng 1 W10852104 (CNTRL-ELEC) and 1 W10852683 (NAMEPLATE) and 1 WPW10225960 (PANEL-DOOR)"
Aris S.
DRYER WHIRLPOOL WGD92HEFW1 "Run unit on service diagnostic, error e3-f4, restricted air flow, customer need to check the vent"
Eric P.
LAUNDRY MAYTAG MVWB765FW2 "Ep-unit has F3E2(inlet water temp),F8E1(long fill) error codes-cleared. Tested valves in diagnostics-trickle, manually tested valves-no/trickle of water, ohmed well out of range 926-1016 across the valves, temp thermistor is also out of range. Ordering (1) W11165546 valve; ordrng 1 W11165546 (VALVE)"
Dennis B.
WASHER WHIRLPOOL WTW8500DW5 Db took of both hot and cold lines off no water coming in to unit cust to contact her plumber
Robert D.
MICROWAVE KITCHENAID KEMC308KSS0 "Unit has faulty mag and transformer. Quoted cust $825.28 ($235.00 transformer, $285.00 mag, $165.00 lab, $89.00 2nd man) cust declined repairs at this time due to cost and age of unit. Parts needed are WP4375424 and WP4375286."
Darren S.
DRYER WHIRLPOOL MGDC465HW0 Found belt came off drum and idler pulley .. secure belt .. ran cycle .. machine ok
Aris S.
OVEN WHIRLPOOL KEBS208SSS00 Need parts; ordrng 1 W10877014 (GASKETS) and 1 WP4448933 (RETAINER )
Mike G.
M/W OTR WHIRLPOOL WMH31017AS0 Transformer smells like it’s burning. Needs new transfomer. Gave cust est.
Sam C.
REF BOT/MT 22CF KITCHEN-AID n/a Unit with sealed system leaks need to be flushed on return advised customer unit need to be off the platform to perform work; ordrng 1 4387444 (evap repar) and 1 W10507884 (compressor) and 1 WPW10317013 (evaporator)
Arden D.
DRYER MAYTAG MGDC300BW1 "AD. Checked unit, found faulty thermal fuse. Replaced defective fuse. Unit tested ok.; used 1 WP3392519 (FUSE) from stock"
Trevor B.
TRIO CD WHIRLPOOL WRF540CWHZ01 TB- Unit needs replacement Freezer door (cosmetic damage). ; ordrng 1 W11301143 (FREEZER DOOR )
Eric S.
KITCHEN WHIRLPOOL WDF540PADW3 Tested unit it is working as designed no noise
Aris S.
REFRIG/FREEZER WHIRLPOOL WRF560SEYM05 "Clean up the drain line, & ajusted the freezer door, test it is ok"
Eric S.
WASHER MAYTAG MVWC416FW0 Tested unit no leak found
Stoyan S.
RANGE JENN-AIR JGRP430WP02 Software problem Order new UI; ordrng 1 W10464535 (cntrl-elec)
Karl G.
WASHER MAYTAG MVWX655DW1 Kg 1/29 checked washer found control not advancing into wash cycle. Unit stays on sensing. Reset control through diagnostic calibration setting. Test washer through cycle. All components tested properly. Operating as designed
Efrain R.
DRYER WHIRLPOOL WGD75HEFWO At this time unit us working ok
Clem S.
WASHER WHIRLPOOL LSG7806AAE Found loose damper trapped under pump pulley ; ordrng 1 203956 (damper kit)
Aris S.
OVEN WHIRLPOOL KGBS276XWH0 "Found a bad igniter, install 2 , 2 oven, test it is ok; used 2 W10918546 (IGNTR OVEN) from stock"
Vlad C.
WASHER MAYTAG MVWC200XW1 "Needs parts...; ordrng 1 W10393483 (CONTROL UNIT ASSEMBLY, MACHINE & MOTOR) and 1 W10780048 (SUSPENSION)"
Vlad C.
RANGE AMANA AGR6303MFS0 Alt. (718)681-9369. Office was called. Stated that knobs are not cover. Unit is working fine.
Vlad C.
WASHER AMANA NTW4516FW3 Reseted main control board. Inspected for proper function. Working fine now. Tech explained and customer was ref. to manual for proper installation and how to use it correctly.
Felipe T.
DISHWASHER WHIRLPOOL WDT710PAYM6 "Unit needs sump motor replaced, customer declined estimate"
Clem S.
WASHER WHIRLPOOL WFW3090GW "Found sock trapped between tub and pump. Remove sock trapped in hose ,test okay"
Aris S.
M/W OTR WHIRLPOOL WML55011HS-2 "I call tech line spoke jk sr 7724043569, I call up safety teen, they will call the customer"
Edwin M.
WASHER WHIRLPOOL WFW72HEDW0 Unit tested ok passed diagnostics collected 125 cash
Paul D.
REFRIG/FREEZER WHIRLPOOL WRT519SZDM02 Not getting complete frost pattern on evap ice build up right top side chunk of ice need seal system repair tech only ; ordrng 1 W11092625 (compressor)
Omar S.
WASHER WHIRLPOOL WFW7590FW0 "No error code save pass diagnostics test,instruct to Jose,to not wash rugs and to not over load washer..."
Tim S.
RANGE JENN-AIR JES9750BAS Removed paper from blower reconnected Hose from oven to blower
Felipe T.
DISHWASHER KITCHENAID KDTE254ESS2 Replaced defective right upper rack adjuster ; used 1 WPW10546503 (ADJUSTER) from stock
Mike D.
WASHER MAYTAG MVWC415EW2 Check found no problem with unit at this time operating as design.
Felipe T.
DISHWASHER JENN-AIR JDTSS244GP0 Ran calibration cycle and cleared error code. Advised customer to run hot water prior to starting the dishwasher
Stoyan S.
MICROWAVE KITCHENAID KHMC107EBL2 Ck unit was unplugged Plugged in test it all op ok
Stoyan S.
DISHWASHER WHIRLPOOL WDF110PABW4 Ck unit need new cntrl board amd heating element Customer will make decision later ; ordrng 1 W10518394 (heater) and 1 W11039983 (cntrl-elec)
Eric S.
72" BM WHIRLPOOL KRFC302ESS00 Found clogged drain using rental truck no access to truck stock. Need parts; ordrng 1 W10619951 (DRAIN TUBE )
Marc C.
DRYER MAYTAG MEDB765FW0 Customer education tested and found customer is not holding start button long enough I showed customer how to hold down button so dryer starts unit working as designed no parts needed
Wayne D.
REFRIGERATOR WHIRLPOOL WRS965CIAM00 "Sr#7724049083 replace user interface, order parts; ordrng 1 W10500004 (hinge-door) and 1 WPW10257203 (cam-door) and 1 WPW10476314 (cntrl-elec)"
Marc C.
WASHER MAYTAG n/a Tested and found back legs on washer uneven causing out of balance adjusted rear feet tested unit full cycle spun out OK
Darren S.
WASHER MAYTAG MVWX655DW1 Error codes F7e5 ...f8e1 ... ran diagnostics.. calibrate unit.. customer instruct on fill hoses ..
Roberto C.
LAUNDRY WHIRLPOOL WTW5000DW2 Reset control tested OK
Paul T.
WASHER WHIRLPOOL MVWX655DW1 "Checked unit, unit is hooked up to a different rubber hose that does not come with unit, hose runs along floor and than up through the wall. This is causing water to back-flow into unit and also could cause water to syphon out. Unit will not operate because water goes back into machine and never completely drains causing no spin, unit js operating as designed and test ok but will not work the way it is hooked up. Photos uploaded to file."
Darren S.
KITCHEN WHIRLPOOL WDT730PAHZ0 Error code f7e1 ... ran diagnostics ... no heat .. found open heater .. customer will call back if repairing..
Efrain R.
WASHER MAYTAG MHW3505FWO Replace drain pump ok
Moses D.
RANGE KITCHENAID KSGG700ESS1 Replaced scoop trim. Tested ok
Chris H.
WASHER MAYTAG MVWC416FW1 "CH - found unit with broken agitator barrel - would require new agitator {W10836692} to repair. Unit is being used in an assisted living facility. Called trade partners to report - sr# 7724016055. Per trade partners, unit being used in commercial facility voids warranty unless customer can provide a 5013c form proving that facility is being operated as a non-profit. Left message with a worker for the owner, called owner and left voice mail explaining this. If facility is for profit, customer would be responsible for cost of repair."
Gerry Q.
RANGE KITCHEN AID KDRS483VSS Control interface replaced tested ok
Gerry Q.
DISHWASHER KITCHEN AID KUDK03FTSS3 Unit tested ok by tech no water leak found
Gerry Q.
KITCHEN WHIRLPOOL KDTE334GPS0 Installation issue unit tested ok
George T.
WASHER WHIRLPOOL WTW4816EW2 "Had to replace failed door latch...test ok after repair..also ran diagnostics to refresh..; used 1 W10838613 (LATCH) from stock, Job Cmpltd"
George T.
DISHWASHER WHIRLPOOL WDT730PAHZ0 Nothing wrong with unit itself...found water takes to long to get hot at sink.also not using jet dry..went over the way unit needs to be used.checked voltage feed to unit. Also found ok.
George T.
REFRIGERATOR WHIRLPOOL WRF767SDEM01 Found just the lights on..cooling system completely down..unplugged unit for a bit..replugged into outlet...compressor came on..checked freshfood evaporator..started to frost up properly...good frost pattern...all working well. Before leaving the home...customer to monitor temps...
George T.
DRYER AMANA NED4655EW1 Found new construction and new electrical lines...checked the outlet..i am getting 220v at the outlet..but not getting the proper voltage across both hot legs..customer will need to get in touch with the electrician that wired the outlet..; Job Cmpltd
George T.
WASHER WHIRLPOOL WFW5090GW Had to open door manually with manual release...than found unit was accidently locked out..was able to reboot and get it out of lock mode...ran unit again all features and functions test ok..
George T.
RANGE WHIRLPOOL WFG320M0BS0 Had to replace weak bake ignitor. Test ok after repair..; used 1 12400035 (igniter) from stock
Edwin M.
REFRIGERATOR WHIRLPOOL WRT111SFDM03 Adjusted tstat probe unit tested ok
Edwin M.
REFRIG/FREEZER WHIRLPOOL WRT519SZDW02 Replaced part unit tested ok
Gerry Q.
TRASH COMPACTOR KITCHEN AID KTTS505ESS Directional switch replaced tested ok; used 1 WP777811 (SWITCH DIR) from stock
Darren S.
DISHWASHER KITCHEN AID KDPE234GPS0 Error code 7-1 ... ran diagnostics ...heater on .. machine ok ..
Robert D.
RANGE JENN-AIR JGRP436WP02 Replaced spark module assm. No further issue. Unit no longer continues to click.
Robert D.
RANGE KITCHENAID KSEG700ESS2 Installed correct panel. Prev panel was indeed incorrectly packaged. All operations are responsive. No further issue.
Robert D.
LAUNDRY MAYTAG MVWB765FW2 Checked unit. removed small article of clothing under washplate. Unit is now working as designed.
Tyler S.
72" BM JENN-AIR JFC2290VEP8 "Icemaker was faulty not calling for water, installed new icemaker from truck and installed water valve. Filled with water tests good. Advised to dump first few batches and allow time for ice production.; used 1 W10884390 (ICEMAKER) from stock"
Tyler S.
DRYER MAYTAG MGDC200XW2 "Installed new thermal cutoff, now heating and tests good. Advised to have venting cleaned."
Tyler S.
LAUNDRY MAYTAG MVWB765FW1 "F0E3 off balance, F0E5 overload, F7E8 motor over temperature. Unit passed all diagnostic tests and basket turns freely. More then what machine can handle is being loaded into it. Educated customer over the phone as he was not home for appointment and had someone that doesn’t use washer home for the appointment."
Tyler S.
DRYER AMANA NGD4655EW2 Found front panel felt peeled backwards which was causing thumping noise while drum was turning. Reseated felt properly and unit now runs noise free.
Robert D.
WASHER WHIRLPOOL WFW9400SW01 "Unit has faulty bearing. Cust declined repairs due to cost being over $1,000 for repair and unit being over 10 years old. Cust will replace unit. Collected $122.57"
Brian H.
M/W OTR WHIRLPOOL WMH75021HZ1 Assisted to Replac partsWorking ok
Brian H.
REFRIGERATOR KITCHENAID KSC24C8EYY02 "Repaired with out parts, removed obstruction from drain line"
Brian H.
DISHWASHER WHIRLPOOL DU915PWWS1 "Repaired with out parts, removed obstruction from drain pump.Working ok"
Brian H.
REFRIG/FREEZER WHIRLPOOL WRS325SDHZ02 "Repaired with out parts, Adjusted cardboard beneath condenser coil near front of unit. Running quietly."
Eddy P.
DRYER WHIRLPOOL WED7990FW0 Dryer heat is good ran full test could not find any issues with dryer instruct customer should clean back of the fence unit is normally going to get hot or exhaust hot air through the back. Instruct customer must have full load when using the sensor setting
Eddy P.
DRYER MAYTAG MED6000XG2 "Replaced pulley and bad roller with the roller support original noise is gone but ran test unit still has a rattling noise coming from the cabinet could not find the source of the rattling instruct customer, customer said unit was already making that noise could not repair it. Rattling noise coming from cabinet of dryer"
Eddy P.
WASHER WHIRLPOOL WTW4915EW2 Hot water is off need to put washer only on tap cold water for it to work
Eddy P.
WASHER WHIRLPOOL WFW3090GW Reset flood stop sensor unit was working OK water was coming into the washer show the handyman/door man before and after her unit was working after I reset it before I reset it was not working explain to him must change the flood stop sensor board completely get a new one and install it. Has nothing to do with the washing machine
Kenly S.
RANGE AMANA AGR4230BAW1 part is stacked and is working well
George T.
WASHER WHIRLPOOL WTW5000DW1 Hot water valve on wall not working at all..needs to be replaced by customer.water does not come in properly.control does not activate properly..unit intermittenly goes on and off...; ordrng 1 W11116590 (cntrl-elec) and 1 W11307244 (LATCH)
Edwin M.
REFRIG/FREEZER WHIRLPOOL WRF560SEHZ00 Adjusted temp setting. Were set to low. And ran water line to clear filter carbon
Edwin M.
REFRIG/FREEZER WHIRLPOOL WRF560SEM05 Adjusted filter housing found clip installed incorrectly
Kenny G.
DISHWASHER KITCHEN AID KDTM354DSS3 Installed pump job don e
Darren S.
WASHER MAYTAG MVWC300VW1 Install parts.. same issue .. power to valve ; ordrng 1 W10144820 (VALVE)
Kenny G.
WASHER COMM WHIRLPOOL CAE2745FQ0 Installed both parts job done
Kenny G.
WASHER WHIRLPOOL WTW8600YW0 Ran service diagnostics. Tests passed. Reset main control. No errors.
Robert D.
RANGE - ELECTRIC JENN-AIR JES8850CAS02 Only one hinge was ordered. Need to replace both to correct door sagging issue. Left parts with cust. Ordering hinge. ; ordrng 1 74011475 (HINGE )
Kenny G.
DISHWASHER WHIRLPOOL WDF330PAHW1 "1 apt //// checked unit; found drain punp clogged .. cleared pump; retested; Job Cmpltd, saved tckt"
Kenny G.
WASHER MAYTAG MVWX655DW1 Installed main board unit working as designed by manufacturer.
Kenny G.
WASHER WHIRLPOOL WTW5000DW2 checked unit; not working ; reProgrammed unit. Work ok
Kenny G.
REF T/M 18 CFFF WHIRLPOOL WRT518SZFM00 "Fixed ice maker fill issue ; Job Cmpltd, saved tckt"
Paul D.
REF S/S 25 CF WHIRLPOOL WRS325FDAM04 cleaned out. Unit tested ok.
Tyler S.
ALPHA WHIRLPOOL WFW70HEBW2 Unit won’t ramp up to highest spin speed. C8 in diagnostics fails to work properly but no codes stored in unit. Spoke with tech-line who stated no MCU on unit that motor controls are built into main control. Needs new CCU. SR#7724017900 ; ordrng 1 WPW10635660 (CCU)
Paul D.
DRYER WHIRLPOOL LSE7804ACE unit tested ok.
Paul D.
WASHER WHIRLPOOL WFW8740DW0 Cleared codes. Unit tested ok.
Tyler S.
DISHWASHER WHIRLPOOL WDF520PADM7 "Installed new friction pads, tests good."
Kyron G.
RANGE KITCHENAID KSGB900ESS1 unit tested ok.
Brian H.
DISHWASHER KITCHENAID KDTM354ESS0 Diagnosed seized pump assembly W10805015Order parts; ordrng 1 W10805015 (PUMP ASSEMBLY)
Kyron G.
DISHWASHER WHIRLPOOL WDF520PADM7 used 1 w10876537 from stock
Kyron G.
REFRIG/FREEZER AMANA ASD2575BRS01 unit tested ok.
Clayton G.
OVEN WHIRLPOOL KOCE507EBS03 Replaced switch unit tests ok.
Mike G.
DISHWASHER KITCHEN AID KUDE40FXSS1 Installed parts working fine
Aris S.
WASHER WHIRLPOOL WTW5000DW1 Install parts test it is working normal
Aris S.
WASHER WHIRLPOOL CAE2743BQ0 "Run unit on service diagnostic, unit is working normal at present time., but if problem continues then need to send the control w10860464 & actuator w11212745"
Eddy P.
DRYER MAYTAG LSG7806AAE Customer needs rollers and pulleys replaced unit is squeaking instruct customer should get rollers and she have to replace the pulley and bracket. Customer will pay the full amount when the job is done; ordrng 2 12001541 (cables)s and 1 303836 (BLOWER) and 1 WP6-3033630 (idler arm) and 1 WP6-3037050 (pulley) and 2 WP6-3129480 (cables)s and 1 WPY312959 (belt)
Aris S.
OVEN WHIRLPOOL WFG505M0BS3 "Set door gasket, back on place , test it is ok"
Omar S.
WASHER WHIRLPOOL WTW5000DW1 Installed transmission test ok...Ariss will return the outer tub.
Kenly S.
DISHWASHER KITCHENAID KDTE104DSS1 check and found that MOTOR is damaged; ordrng 1 W11032770 (MOTOR)
Kenly S.
REFRIG/FREEZER WHIRLPOOL WRS325FDAW04 check and found that the lights are defective; ordrng 2 WPW10515057 (LIGHT)s and 1 WPW10515058 (LIGHT)
Omar S.
DRYER AMANA NGD4655EW2 "Poor air flow,Instruct costumer vent need to be clean and check.."
Kenly S.
REF BOT/MT 19CF WHIRLPOOL n/a check and found that the filter could be blocked; ordrng 1 EDR1RXD1 (FILTER)
Omar S.
WASHER WHIRLPOOL WFW7590FW0 No water entering the washer need to get a plumber and check the water pipe.
Frank G.
LAUNDRY WHIRLPOOL WTW7040DW1 Needs lid lock assembly S Code (S61361) for part...; used 1 W10810403 (LID LOCK) from stock
Stan F.
OVEN WHIRLPOOL KOCE507EBS03 I’m the helper on this call ok.
Kenny G.
REFRIGERATOR WHIRLPOOL WRX735SDHZ00 Led module is not working. ; ordrng 1 W10866538 (module)
Clayton G.
M/W OTR WHIRLPOOL WMH32519HB0 Replaced cp diode mag unit tests ok
Kenny G.
M/W OTR KITCHENAID KHMC1857XSP0 Door switches acting up. Interlock failure. ; ordrng 1 W11244490 (INTERLOCK KIT )
Clayton G.
WASHER AMANA NTW4516FW1 AIKUY00EPL1 unit had power loss. Recap tests ok
Clayton G.
M/W OTR WHIRLPOOL WMH76719CS5 Unit tests ok pulls napkin up as designed by mfg.Refer to pictures of test.Customer was not satisfied with airflow. Unit vented inside. Not outside.
Clayton G.
RANGE WHIRLPOOL WFE770H0FZ1 Replaced lft front burner switch. Unit tests ok
Stan F.
M/W OTR WHIRLPOOL WMH32519HB0 I’m the helper on this call ok.
Jason T.
M/W OTR MAYTAG MMV1174FZ0 "Replaced defective computer board & switch assembly, tested ok..."
Jason T.
COOKTOP WHIRLPOOL JGC9536BDS17 "Replaced defective spark module & switches, tests ok...; used 1 542638 (GREASE) from stock"
Jason T.
REFRIG/FREEZER KITCHENAID KRFC300ESS01 "Made checks” tighten freezer door handle, tested ok..."
Wayne D.
REF S/S 27 CF WHIRLPOOL WRS537SIAM01 Replaced filter housimg
Paul D.
REFRIGERATOR WHIRLPOOL WRF535SWHZ00 ordrng w10890275/left ref door (by SX)
Wayne D.
REFRIG/FREEZER WHIRLPOOL WRF560SEYB01 Replaced tracks
Wayne D.
ICEMAKER KITCHENAID KUID508ESS2 Replaced ice maker grid
Efrain R.
MICROWAVE WHIRLPOOL KMHC319EWH4 Assist stoyan with m/w ok
Jesse F.
REF T/M 21 CFFF WHIRLPOOL WRT511SZDM00 "Replaced t/stat, adaptive timer, door endcaps and track..."
Roberto M.
DRYER WHIRLPOOL WGD9470WW2 Rplc part test ok...
Roberto M.
DRYER MAYTAG MEDC465HW0 Rplc part test ok...
Roberto M.
WASHER MAYTAG MVWX655DW1 Checekd unit. cleaned debris from pump and reset computer test ok..
Roberto M.
DRYER WHIRLPOOL WGD5800BW Rplc coil test ok...
Aris S.
RANGE WHIRLPOOL WFG505M0BS3 Need parts ; ordrng 1 W11176456 (GLASS DOOR )
Brian H.
ICEMAKER JENN-AIR JIM158XYCX1 Diagnosed faulty control board W11034363Parts $270.34Labor $75Svc. $114.95Total estimate to repair $460.29 plus taxCustomer does not wish to repair at this time. Will call if they change their mind and wish to order part.
Trevor B.
M/W OTR WHIRLPOOL WMH75021HZ1 "TB- Installed new magnetron, diode and capacitor. Tests good."
Frank G.
DRYER WHIRLPOOL WGD9470WW2 Replaced valve and checked...
Aris S.
DISHWASHER WHIRLPOOL KDTE404DSS0 "Run unit on service diagnostic , need parts ; ordrng 1 W10866116 (CONTROL BOARD ) and 1 WPW10537418 (CONSOLE )"
Frank G.
WASHER WHIRLPOOL WTW7000DW3 Needs housing....replaced prescreened part...also needs house filter to catch silt from well pump that clogs inlet valve...
Omar S.
WASHER WHIRLPOOL WTW4950HW1 Not starting need control board.; ordrng 1 CONTROL BOARD
Stoyan S.
MICROWAVE WHIRLPOOL KMHC319EWH4 Replace defective thermostat Test it all op ok
Omar S.
WASHER WHIRLPOOL WTW5000DW1 Ring tub is peeling off need part...; ordrng 1 W10849477 (ring-tub)
Stoyan S.
DISHWASHER WHIRLPOOL WDF520PADM7 Loose wire nut Re install Test it all op ok
Stoyan S.
DISHWASHER JENN-AIR JDB9800CWS2 Replace defective drain pump/ clean hose under sink /test it all op ok
Arden D.
MICROWAVE JENN-AIR JMW2430WS02 AD. Assistance with repair completed. Unit ok.
Arden D.
DISHWASHER WHIRLPOOL WDTA50SAHZ0 "AD. Checked unit, found spoon under float. Removed spoon, float switch now operating properly. Unit tested ok."
Clayton G.
DISHWASHER WHIRLPOOL WDT730PAHZ0 Unit needs sleeve. WP8268961; ordrng 1 WP8268961 (pad)
Felipe T.
MICROWAVE JENN-AIR JMW2430WS02 Replaced defective microwave control board
Felipe T.
RANGE WHIRLPOOL WEG750H0HZ0 Installed burners
Moses D.
RANGE KITCHENAID KDRS483VSS04 Replaced broken adapter. Tested ok no leaks
Trevor B.
DISHWASHER KITCHENAID KDTE254ESS2 TB- Customer stated he called to cancel appointment.
Peter B.
WASHER WHIRLPOOL WFW5090GW Need ccu control PD have pump 2 men 3counts; saved tckt
Damion M.
DRYER WHIRLPOOL WGD88HEAW1 "1/28/19 9:33: DM rspndd 1/25 FRI, Installed wheel & motor. Unit tested ok."
Wayne L.
MICROWAVE KITCHENAID KHMC1857BSS1 "Check unit cam and support was faulty installed part unit working fine ; used 1 W10562613 (CAM - PLATE), and 1 WP8206419 (SUPPORT) from stock"
Moses D.
RANGE WHIRLPOOL WFE540H0ES1 Replaced control elec and temp sensor. Tested ok
Moses D.
COOKTOP WHIRLPOOL WEE510S0FV2 "Made checks found spot on right rear burner, was able to remove to cleaner and razor. Tested okTold customer to keep an eye on burner"
Brian H.
REFRIG/FREEZER JENNAIR JFC2290REM00 "Door switch has been glued to unit, i am unable to remove it.I will need to force it out and repair liner. Order touch up paint 72017 and touch up paint 511873; ordrng 1 511873 (PAINT) and 1 72017 (TOUCH UP PAINT)"
Vincent D.
ICEMAKER KITCHENAID KUIX305ESS2 Vd installed part tested unit ran to specs
Vincent D.
WASHER MAYTAG MVWB865GW0 Vd found 1 code for overload cleared ran diagnostics no issues ran a calibration cycle on unit found no issues at this time called tech line was advised no issue give cust education ref # 7724015547
Mike G.
RANGE KITCHENAID KDRS483VSS04 Installed part working fine
Mike G.
KITCHEN WHIRLPOOL WDT720PADM2 Console no good cycle not working. Part number w10815487. $ 227.25. Labor 90.00. And taxes. Customer going to think it over.
Frank G.
WASHER WHIRLPOOL WTW5000DW2 Needs control assembly...order control and return ; ordrng 1 W11116590 (CONTROL )
Mike G.
DRYER WHIRLPOOL WED4850HW0 Installed parts working fine
Mike G.
DISHWASHER WHIRLPOOL WDT720PADM2 Installed part working fine
Stoyan S.
RANGE JENN-AIR JDS1750FP0 Order new burner cap Send part direct to customer ; ordrng 1 WPW10300347 (cap-burner)
Matt S.
LAUNDRY MAYTAG MVWB865GW0 New suspension mounts and tub ring installed. Working properly.
Jose R.
DRYER EL WHIRLPOOL WED4850BW0 "Found open heating element,replaced with new element and hi-limit thermostat...tested unit ok..also advised to have vent checked,,; used 1 279838, and 1 3977767 (HI-LIMIT THERMOSTAT) from stock"
Jose R.
REFRIDGERATOR N/A ED2KHAXVB01 Replaced defective ice motor..tested ok
Arden D.
OVEN WHIRLPOOL WFG320M0BS3 "AD. Checked unit, found faulty igniter and control. Ordering parts.; ordrng 1 W11126814 (CONTROL ) and 1 W11176454 (IGNITER )"
Felipe T.
KITCHEN WHIRLPOOL KUDE70FXSS5 Ordered control panel ; ordrng 1 WPW10481144 (panel-cntl)
Felipe T.
DISHWASHER WHIRLPOOL WDF560SAFT2 Ordered sump and motor ; ordrng 1 W11085683 (pump&motor)
Arden D.
STOVE WHIRLPOOL WFG540HOES1 AD. Replaced defective burners. Unit tested ok.
Arden D.
DISHWASHER WHIRLPOOL WDF330PAHW2 "AD. Checked unit, ran cycle. Unit functioned within designed operation. No leaks detected. Unit ok."
Felipe T.
DISHWASHER KITCHEAID KDTM404ESS0 Ordered pump and motor ; ordrng 1 W10861526 (pump&motor)
Arden D.
REFRIG/FREEZER WHIRLPOOL WRX735SDBM04 AD. Replaced defective ice bin. Unit tested ok.
Efrain R.
COOKTOP WHIRLPOOL WCG51US6DSOO Replace electrode wire ign . Tested ok
Efrain R.
REFRIGERATOR WHIRLPOOL WRF555SDFZ05 Found filter not set in correctly to make contact to switch .reset ok
Marc C.
REFRIGERATOR WHIRLPOOL GS6SHAXMS00 Tested unit found relay on main control board sticking and clicking ; ordrng 1 WPW10135090 (cntrl-elec)
Efrain R.
WASHER WHIRLPOOL WFW75HEFW0 Replaced harness and ui assy .advance to drain and spin ok. Before washer was filling up where it should spin and drain . Ok
Jose R.
WASHER WHIRLPOOL WTW4816FW2 Found faulty control electric ; ordrng 1 W11170319 (CONTROL ELECTRIC )
Karl G.
KITCHEN WHIRLPOOL KODE507ESS04 "Kg 1/25 checked oven. Doors closing and sealing properly. Unit installed level., lights shuts off when doors are closed. Advised customer doors are operating properly. Oven operating as designed"
Keyel H.
REFRIDGERATOR WHIRLPOOL WRX988SIBE01 Fill tube frozen run test 19 check 120v to heater connector order parts needed.; ordrng 1 WPW10554299 (heater) and 1 WPW10589837 (cntrl-elec)
Damion M.
REFRIDGERATOR KITCHENAID KRFF302ESS01 ordrng wpw10469286/icemaker (by SX)
Karl G.
OVEN WHIRLPOOL GW397LXUS06 Kg 1/25 checked oven found unit not heating. Removed bottom oven cover found ignitor burnt out. Replaced bake ignitor. Unit heating and operating as designed; used 1 74007498 (IGNITOR) from stock
Karl G.
RANGE - GAS WHIRLPOOL GFG474LVS0 Kg 1/25 checked unit found burners not igniting when knobs are turned. Removed front and rear panel to access components. Power to spark module. Found loose connector on spark module. Fastened connector. Tested unit through igniting. All burners tested ok. Operating as designed
Eric P.
REFRIG/FREEZER KITCHENAID KRFC704FBS00 "Ep-unit has frozen r/c evap. Service pointer #W11329116B covers this issue completly and provides Scode. Ordering (1) W11167902 cover-evap, (1) W11333076 contrl-elec; ordrng 1 W11167902 (COVER-EVAP) and 1 W11333076 (CONTRL-ELEC)"
Chris H.
ALPHA WHIRLPOOL WFW87HEDW1 CH - installed new control panel - tests good
Moses D.
WALL OVEN JENNAIR JJW3830WS02 F8E0 error code for cooling fans. Ordering parts; ordrng 1 WPW10273666 (FAN) and 1 WPW10273667 (FAN)
Trevor B.
RANGE JENN-AIR JGS1450FP0 TB- Found bake ignitor warped away from burner tube not allowing spark to ignite gas. Corrected issue. Cleared F2 E1 (stuck key) error. All unit functions test good at this time.
Gabino P.
DRYER WHIRLPOOL WED7990FW0 Replace damage motor and check ok.
Gabino P.
WASHER WHIRLPOOL MHW8200FW0 Replace DESPENCER control electronic and check
Mike G.
N/A N/A n/a Shock no good ; ordrng 4 WPW10261492 (Shock)s
Marc C.
WASHER WHIRLPOOL WTW4816FW2 Tested unit fill wash drain and spin found subfloor uneven unit tilted to the back wall causing unbalanced condition advise customer to shim up back feet with plywood to level unit unit working as designed
Marc C.
REFRIGERATOR KITCHENAID KFIS20XVMS4 Tested unit found front user interface burnt out possibly from power surge parts no longer available cannot be repaired customer wants new unit.
Elmer A.
WASHER MAYTAG MVWC565FW0 Installed valve checked operation ok.
Gabino P.
WASHER WHIRLPOOL WTW5000DW1 Replace broken control electronic and check ok
Gabino P.
DRYER MAYTAG MGDB835DC4 Replace latch and check ok.
Mike G.
DISHWASHER WHIRLPOOL WDT710PAHZ1 Getting code for bad control f7 e3; ordrng 1 W11087213 (CONTROL )