Need Appliance Repair Service? Have a general question?
We love solving problems! Let us know how we can help by reaching out below.

How can we help? Do you need appliance repair?

Local Reviews
for Oceanport, NJ

Dan Marc Appliance Rated 5.0 out of 5 stars based on 2 customer reviews

Map of Oceanport, NJ

Janet Spiwak




Review of Dan Marc Appliance

The person who fixed our dryer was patient and explained what the problem was.


Map of Oceanport, NJ

Great service




Review of Dan Marc Appliance

The process was excellent and the service man was friendly and courteous


Brian H.

Brian H.

DISHWASHER KITCHENAID KDTE204EPA4 Found unit not responding and full of water. Repaired connection to drain pump and rebooted ACU. Unit working as designed.

Near Iroquois Ave, Oceanport, NJ 07757
Brian H.

Brian H.

DISHWASHER WHIRLPOOL WDT730PAHZ0 Diagnosed and replaced faulty rack adjusters W10712395. Working ok.

Near Manitto Pl, Oceanport, NJ 07757
Vincent D.

Vincent D.

WASHER WHIRLPOOL WTW8500DC0 Vd found a sheer bed cover stuck under stator removed and tested unit codes were a cause of sheet under stator ran diag and on spin unit completed cycle

Near Nicholson Pl, Oceanport, NJ 07757
Chris H.

Chris H.

DRYER - GAS WHIRLPOOL WGD8500DC3 "CH - found leak from water line connection to steam valve on dryer. Resecured connection with teflon tape - no leak detected. No other functional issues found at this time. Customer paid service fee plus tax, $126.21 total by check# 5746"

Near Comanche Dr, Oceanport, NJ 07757
Chris H.

Chris H.

REFRIGERATOR WHIRLPOOL WRF954CIHW01 "CH - manually deiced rc evaporator, installed new evap cover, and optimized thermistor position. Tests good. Set temps to recommended with max cool on and advised customer to allow 24-48 hours for temperatures to normalize"

Near Port Au Peck Ave, Oceanport, NJ 07757
Chris H.

Chris H.

DRYER WHIRLPOOL WED8000DW4 CH - found idler pully seized onto shaft of idler assembly - inner spindle of pully wheel was damaged. Replaced from repair kit {4392067} - tests good

Near Iroquois Ave, Oceanport, NJ 07757
Chris H.

Chris H.

DISHWASHER WHIRLPOOL KDTE254ESS2 "CH - found unit with stored f6e4, f6e1 faults. Adjusted float switch and ran unit on normal setting - unit fills, circulates water, and drains normally. Found a large amount of suds in tub - advised customer to use vegetable oil trick to clear suds and then immediately run a clean cycle with affresh to resolve. No other functional issues found at this time. Customer paid service fee plus tax, $126.21 by credit card, ref# 1952604702"

Near Wittenburg Ct, Oceanport, NJ 07757
Chris H.

Chris H.

DISHWASHER WHIRLPOOL KDTM404EWH0 "CH - unit needs new control {W10854228}, sump {W10861526}($244.15). Per service bench, control covered under 60 mo extended parts warranty. Gave customer estimate for repair: service fee $117.95, parts $244.15, labor $95, tax $32, total $489.10. Customer paid in full by credit card, ref# 1952578169; ordrng 1 W10854228 (CONTROL) and 1 W10861526 (SUMP)"

Near Surrey Ct, Oceanport, NJ 07757
Chris H.

Chris H.

WASHER WHIRLPOOL WFW9400SW01 "CH - found evidence of small leak from bellow in base 9f unit. Put unit into diagnostics to verify leak - as soon as door lock engaged, the gfi outlet the unit is plugged into blew. Reset gfi, unit powered back on and attempted to unlock - blew the gfi again. Ohmed out door switch at DLS2 connector - reads openline with switch open and closed. Called techline to document, sr# 7726798882. unit needs new door lock {WP8183270}($118.56), bellow {WP8182119}($163.91). Gave customer estimate for repair: service fee $114.95, parts $282.47, labor $95, tax $34.47, total $526.89. Customer paid service fee plus tax, $122.57 by check# 1104"

Near Ausable Ave, Oceanport, NJ 07757
Chris H.

Chris H.

DRYER WHIRLPOOL WGD9400SW1 CH - found and removed metal foreign object from blower housing - no other functional issues found at this time. Service fee paid on invoice# 839968

Near Ausable Ave, Oceanport, NJ 07757
Eric P.

Eric P.

WASHER WHIRLPOOL WTW8040DW4 "Ep-Installed new gearcase, tested and ran calibration. Machine functions as designed"

Near Long Branch Ave, Oceanport, NJ 07757
Chris H.

Chris H.

DISHWASHER WHIRLPOOL KDTE334GPS0 CH - installed new upper rack adjusters - tests good

Near Port Au Peck Ave, Oceanport, NJ 07757
Chris H.

Chris H.

DISHWASHER WHIRLPOOL KDTE334GPS0 CH - unit needs new upper rack adjuster x2 {WPW10546503}; ordrng 2 WPW10546503 (ADJUSTER)s

Near Port Au Peck Ave, Oceanport, NJ 07757
Eric P.

Eric P.

DRYER AMANA NGD4655EW2 "Ep-timer doesnt shut off. Ran test cycle and timer advanced properly but stays on cool down without reaching “end”. Needs new timer. Quoted $378.84=trip$114.95, parts$165.35,labor$75.00,tax$23.54. Must contact office for payment . Unit will need (1) W10857611 timer if office approves"

Near Gosselin Ave, Oceanport, NJ 07703
Eric P.

Eric P.

OVEN WHIRLPOOL WFG320M0BS3 Ep-Installed new seal

Near Gosselin Ave, Oceanport, NJ 07703
Chris H.

Chris H.

REFRIGERATOR KITCHENAID KRFC704FPS03 CH - installed new ice maker - tests good. Advised customer to discard any ice produced in first 24 hours

Near Haskell Way, Oceanport, NJ 07757
Chris H.

Chris H.

WASHER WHIRLPOOL WTW8040DW4 "CH - while attempting repair, found washplate screw seized onto drive shaft. Could not remove, even with corded impact gun. Drive shaft has a spanner nut, so cracking the washplate off without removing the screw will not work. Called techline to report, sr# 7726486874. Unit needs new screw {W10752187}, washplate {W10775188}, spanner nut {W10909670}, basket {W10811960}, tub {W11219115}, screw {WPW10109200}, filter {WPW10215093}, washer {W11032711}, 2 techs and 3 job count on return; ordrng 1 W10752187 (SCREW) and 1 W10775188 (WASHPLATE) and 1 W10811960 (BASKET) and 1 W10909670 (SPANNER NUT) and 1 W11032711 (WASHER) and 1 W11219115 (TUB) and 1 WPW10109200 (SCREW) and 1 WPW10215093 (FILTER)"

Near Long Branch Ave, Oceanport, NJ 07757
Eric P.

Eric P.

REFRIGERATOR KITCHENAID KFIV29PCMS03 "Ep-pressures in test#4/4 of 5/150 drier is warm, pressures in test#4/5 of -12/150 drier is cold. Goes into vacuum when shifting sides. No visible dye on evaps or connections. Recovered minimal charge and re-charged with nitrogen (150psi) dropped 3psi every 15min until empty. Contacted techline-Kathy(sr#7726427274)-must remove thermistors from both evaporators and inspect for scaring,leak or nitrogen bubbles. Retested after inspecting around thermistors, no visible issue. Contacted techline-Kevin(sr#7726494535)-being sent for review. Customer will contct trade partners in 24hrs"

Near Blue Point Cove, Oceanport, NJ 07757
Eric P.

Eric P.

WASHER AMANA NTW4516FW2 "Ep-unit has a cracked/broken outer tub, needs replacement. Quoted $456.56, trip=$114.95,parts=$178.24,labor=$135.00,tax=$28.37. Invoice needs to be emailed to sshapiro@rpmdev.com and call susan @ 1-203-943-4112 for payment"

Near Gosselin Ave, Oceanport, NJ 07703
Chris H.

Chris H.

DISHWASHER WHIRLPOOL WDT750SAHZ0 "CH - unit needs new control {W11305297}, sump {W10917114}; ordrng 1 W10917114 (SUMP) and 1 W11305297 (CONTROL)"

Near Turf Dr, Oceanport, NJ 07757
Eric P.

Eric P.

REFRIGERATOR KITCHENAID KRFC704FPS03 "Ep-unit is not producing ice, test #120 icemaker didnt move/return to home position. Bail arm is stuck in the down position and tray is is dispense position. Ordering (1) W11115534 icemaker; ordrng 1 W11115534 (icemaker)"

Near Haskell Way, Oceanport, NJ 07757
Eric P.

Eric P.

WASHER WHIRLPOOL WTW8500DC0 Ep-Installed new washplate

Near Nicholson Pl, Oceanport, NJ 07757
Eric P.

Eric P.

REFRIGERATOR KITCHENAID KFIV29PCMS03 "Ep-between product F/C temp of 23°-all products in freezer are frozen. R/C temps of 43°-temps are slightly elevated. Found E1 error(temps above 45° for more than three hours) test #37 -passed. Rescheduling for 11/26/19 with extra time to remove unit ,check for leaks and recharge system; ordrng 1 EXTRATIME"

Near Blue Point Cove, Oceanport, NJ 07757
Eric P.

Eric P.

WASHER WHIRLPOOL WTW8500DC0 "Ep- u it had F0E3(overload),F0E5(off balance), F8E1(long fill) error codes-cleared. Washplate spin freely, removed and ran diagnostics -completed. Cleaned teeth of washplate and re-Installed testing heavy agitate. Ordering (1) W10752283 washplate; ordrng 1 W10752283 (washplate)"

Near Nicholson Pl, Oceanport, NJ 07757
Eric P.

Eric P.

REFRIGERATOR KITCHENAID KRMF706ESS01 "Ep-Installed new switch, tested operation. Small 1-3 second delay before all water flow stops-unable to find any information on how fast that should stop. Adjusted water valve to slow pressure rate.Machine functions as designed"

Near Pocano Ave, Oceanport, NJ 07757
Eric P.

Eric P.

WASHER WHILPOOL NTW4516FW2 "Ep-ran diagnostics and manually tested valves, unable to replicate. Invoice needs to emailed to main office"

Near Gosselin Ave, Oceanport, NJ 07703
Chris H.

Chris H.

WASHER WHIRLPOOL WTW8040DW4 "CH - customer complaint of intermittent grinding noise during cycle. No stored error codes. Found large amount of oil leaking from gearcase on stator rotor. Unit needs new gearcase {W10811956}, 3 job count on return; ordrng 1 W10811956 (GEARCASE)"

Near Long Branch Ave, Oceanport, NJ 07757
Eric P.

Eric P.

REFRIGERATOR KITCHENAID KFIV29PCMS03 "Ep-unit has multiple issues that will impact cooling and ice production. Faulty pantry U/I, mullion that doesnt close properly and bad freezer door( gasket falls out of expanded liner gap-currently i taped it in place). Ordering (1) W11199439 cntrl-elec, (1) LW10564038 SERVICE-FZDW,29,SS,XXL FIP, (1) W10407216 GASKET-DOOR,AP,FZDW, (1) W10849525 rail-mulln; ordrng 1 LW10564038 (SERVICE-FZDW,29,SS,XXL FIP) and 1 W10407216 (GASKET-DOOR,AP,FZDW) and 1 W10849525 (RAIL-MULLN) and 1 W11199439 (CNTRL-ELEC)"

Near Blue Point Cove, Oceanport, NJ 07757
Eric P.

Eric P.

RANGE WHIRLPOOL KSGG700EWH0 "Ep-Installed new sensor, tested unit-Bake@350°-reached temp, cycled and failed to re-ignite. Contacted TB and techline -Andrew(sr#7725188686)-heat aggravated issue, SP# W10622771A/ W10702913A. Scode (1) W10700720 burnr-oven,(1) W10860916 module-spk, (1) WPW10701462 harns-wire; ordrng 1 EXTRATIME and 1 W10700720 (BURNR-OVEN) and 1 W10860916 (MODULE-SPK) and 1 WPW10701462 (HARNS-WIRE)"

Near Surrey Ct, Oceanport, NJ 07757
Chris H.

Chris H.

DRYER WHIRLPOOL NGD4655EW2 CH - installed new coil valve - tests good

Near Gosselin Ave, Oceanport, NJ 07703
Eric P.

Eric P.

RANGE WHIRLPOOL KSGG700EWH0 "Ep-Installed new sensor, tested unit-Bake@350°-reached temp, cycled and failed to re-ignite. Contacted TB and techline -Andrew(sr#7725188686)-heat aggravated issue, SP# W10622771A/ W10702913A. Scode (1) W10700720 burnr-oven,(1) W10860916 module-spk, (1) WPW10701462 harns-wire; ordrng 1 EXTRATIME and 1 W10700720 (BURNR-OVEN) and 1 W10860916 (MODULE-SPK) and 1 WPW10701462 (HARNS-WIRE)"

Near Surrey Ct, Oceanport, NJ 07757
Eric P.

Eric P.

REFRIGERATOR KITCHENAID KFIV29PCMS03 "Ep-unit has multiple issues that will impact cooling and ice production. Faulty pantry U/I, mullion that doesnt close properly and bad freezer door( gasket falls out of expanded liner gap-currently i taped it in place). Ordering (1) W11199439 cntrl-elec, (1) LW10564038 SERVICE-FZDW,29,SS,XXL FIP, (1) W10407216 GASKET-DOOR,AP,FZDW, (1) W10849525 rail-mulln; ordrng 1 LW10564038 (SERVICE-FZDW,29,SS,XXL FIP) and 1 W10407216 (GASKET-DOOR,AP,FZDW) and 1 W10849525 (RAIL-MULLN) and 1 W11199439 (CNTRL-ELEC)"

Near Blue Point Cove, Oceanport, NJ 07757
Chris H.

Chris H.

DRYER WHIRLPOOL NGD4655EW2 CH - installed new coil valve - tests good

Near Gosselin Ave, Oceanport, NJ 07703
Eric P.

Eric P.

REFRIG/FREEZER KITCHEN AID KRFF507EWH01 "Ep-unit has repeat ice buildup on R/C evaporator cover, customer defrosted unit, bottom of evap is still frozen (2 days of defrost). Replacing evap cover, and sealing liner gap, making sure evap tubing is fully recessed behind cover, bringing board as well(will confirm thermistor readings from board on return.Ordering (1) WPW10501260 cover-evap, (1) WP482338 adhesive,ordrng 2 EXTRATIMEs and 1 WP482338 (ADHESIVE ) and 1 WPW10501260 (COVER-EVAP)"

Near Hedge Dr, Oceanport, NJ 07757
Eric P.

Eric P.

DISHWASHER WHIRLPOOL KUDP02FRBL2 "Ep-unit gets no water, confirmed supply valve is open. Tested fill valve at board-OL. Also tested bi-metal. Ordering (1) W10258275 bi-metal, (1) WPW10158389 valve-inlt; ordrng 1 W10258275 (BI-METAL) and 1 WPW10158389 (VALVE-INLT)"

Near S Pemberton Ave, Oceanport, NJ 07757
Chris H.

Chris H.

DRYER WHIRLPOOL NGD4655EW2 CH - unit needs new coil valves {WPW10328463}; ordrng 1 WPW10328463 (COIL VALVE)

Near Gosselin Ave, Oceanport, NJ 07703
Eric P.

Eric P.

WASHER WHIRLPOOL WTW5000DW1 "Ep- Installed new hub, ran diagnostics and calibration. Machine functions as designed"

Near Horseshoe Ct, Oceanport, NJ 07757
Chris H.

Chris H.

REFRIG/FREEZER KITCHEN AID KRMF706ESS01 "CH - installed parts, tests good"

Near Pocano Ave, Oceanport, NJ 07757
Eric P.

Eric P.

RANGE WHIRLPOOL KSGG700EWH0 "Ep-checked for faults-clear, ran diagnostics and no faults. Tested bake @ 350°-reached temp, cycled properly first time, second cycle had ignition and shut off attempting two additional times without ignition. Ordering (1) W10833885 sensor; ordrng 1 EXTRATIME and 1 W10833885 (SENSOR)"

Near Surrey Ct, Oceanport, NJ 07757
Eric P.

Eric P.

REFRIG/FREEZER WHIRLPOOL WRS325FDAM02 "Ep-traced water leak to loose connection at supply valve. Strobe effect in both compartments. And chatter sound when dispenser is in use. Needs new light, reservoir. Quoted $502.35, light $211.41, reservoir $54.78, labor $90.00, trip $114.95. Collected trip by check. Replaced (1)wpw10515057 light from truck stock( broke clip while removing to inspect); used 1 WPW10515057 (LIGHT) from stock"

Near Pemberton Ave, Oceanport, NJ 07757
Eric P.

Eric P.

DISHWASHER WHIRLPOOL WDT720PADM2 "Ep-found loose connection in junction box, repaired and unit powered up. Ran diagnostics-no error codes. Functions as designed"

Near Woodbine Way, Oceanport, NJ 07757
Chris H.

Chris H.

DISHWASHER KITCHENAID KDFE104DSS "CH - reinstalled dispenser door gasket. Unit has no function from wash motor. Found evidence of rodents below unit. Advised customer to contact a licensed exterminator to resolve. Documented with tradecare, sr# 7724727296"

Near Wolfhill Ave, Oceanport, NJ 07757
Eric P.

Eric P.

WASHER WHIRLPOOL WTW8500DC0 "Ep-unit had F5E2,F5E3 error codes-cleared. Unit would trip code immediately and would not start any cycle. Managed to enter diagnostics, lock did work when manually activated. Replaced lock. Also answered a few questions about the dryer"

Near Nicholson Pl, Oceanport, NJ 07757
Chris H.

Chris H.

REFRIGERATOR KITCHENAID KRMF706ESS01 "CH - while attempting repair, found blk wire had come loose from prong in molex connector of replacement harness. Attempted to repair part - could not get the wire back in without special tool. Leaving old harness in, i jumped out molex connector and checkd for continuity at control - found continuity. Reapplied power and checked dc voltage at p2-1 to p2-7 - reading fluctuated between 12.7vdc and 0. Unit needs new control {WPW10624574}, harness {W11170612}, extra time on return; ordrng 1 W11170612 (HARNESS) and 1 WPW10624574 (CONTROL)"

Near Pocano Ave, Oceanport, NJ 07757
Eric P.

Eric P.

72" BM KITCHENAID KFCP22EXMP5 "Ep-unit had small restriction in drain tube ( which was updated in 2014) , removed ice build up from bottom of F/C compartment. Functions properly"

Near Comanche Dr, Oceanport, NJ 07757