Need Appliance Repair Service? Have a general question?
We love solving problems! Let us know how we can help by reaching out below.
Local Reviews
for Ridgefield, NJ
Great service!
Sylvian - Ridgefield, NJ
Felipe T.
RANGE WHIRLPOOL WFG550S0HZ1 "Unit needs convection fan replaced pn#W10794440, blade pn#W10758272. Customer will call Whirlpool to get new authorization#"
Roberto C.
WASHER WHIRLPOOL WFW7590FW0 Needs panel and water valve leaking water and wont start right away 2cc ; ordrng 1 W10599356 (water inlet valve) and 1 W10911022 (panel-cntl)
Roberto C.
WASHER MAYTAG MVWX655DW2 "Run test ,reset control run diagnostics test check ok"
Stoyan S.
D/WASHER UNDCTR KITCHEN-AID KDFE104DSS5 Cntrl panel flashes all the time need new and dispenser broken ; ordrng 1 W10861000 (detergent dispenser) and 1 W11105848 (console) and 1 W11305293 (CNTRL BOARD )
Keyel H.
REF S/S 20 CF WHIRLPOOL WRS571CIDM02 Customer had unit set at 33f in fresh food temp was set to cold instruct customer on temp settings.
Stoyan S.
MICROWAVE KITCHENAID KMHC319ESS2 Customer declined further repair
Stoyan S.
MICROWAVE KITCHENAID KMHC319ESS2 Interlock holder was not installed correctly Re install Test it all op ok
Aris S.
DISHWASHER WHIRLPOOL WDF520PADB7 "Fixed the door strikes, was out of place , test it is working good"
Stoyan S.
DISHWASHER KITCHENAID KUDS01FLSS3 Replace broken links Test it all op ok ; used 1 8194001 (Link) from stock
Gabino P.
WASHER MAYTAG MVWX655DW1 Reset main computer customer washer working ok. ...refused to pay 122.57 trip charges
Gabino P.
WASHER WHIRLPOOL LAT9605AAE 3cct 2 man need replace old transmission decline repair
Keyel H.
REFRIGERATOR WHIRLPOOL WRS325SDHZ01 Unit is now operating normal no leaks.
Gabino P.
DRYER WHIRLPOOL CGM2941TQ1 "Replace coil defective belt cracked roller noise switch loose and check all ok.; used 1 279834 (Coils), 1 341241 (belt), 1 349241T (roller), and 1 WP3406107 () from stock"
Keyel H.
REFRIG/FREEZER WHIRLPOOL WRT318FZDM02 "Seal system problem leak/restriction, will cost to much to fix customer want to replace unit.; ordrng 1 876764 (valve) and 1 W11092625 (compressor)"
Stoyan S.
WALL OVEN JENN-AIR JJW3830DP03 Replace broken glass All op ok
Stoyan S.
DISHWASHER JENN AIR JDB9800CWS2 Replace broken adjuster and missing pivots All op ok; used 1 WPW10546503 (ADJUSTER) from stock
Eric S.
DRYER WHIRLPOOL WED49STBW1 Checked unit working as designed
Gabino P.
WASHER WHIRLPOOL WTW5000DW0 2CCT Need transmission and basket..cell 201-978-6381 leticiaHome 201-945-2337; ordrng 1 W10721967 (cam) and 1 W10752283 (washplate) and 1 W10752719 (basket) and 1 W10913953 (ACTUATOR ) and 1 W11035751 (TRANSMISSION )
Keyel H.
REFRIGERATOR WHIRLPOOL WRF991B00M01 Install parts check ok.
Gabino P.
WASHER WHIRLPOOL CAE2745FQ0 "Replace coin chute computer,control board,; used 1 WPW10491734 (CONTROL ELECTRONIC ) from stock"
Gabino P.
WASHER WHIRLPOOL CAE2745FQ0 Need to replace the control board machine #4; ordrng 1 W11126319 (COIN CHUTE ) and 1 W11188527 (CONTROL BOARD )
Gabino P.
DRYER WHIRLPOOL CG2951XYW0 Replace coil valve check working is ok ; used 1 279834 (Coils) from stock
Omar S.
WASHER WHIRLPOOL CAE2745FQ0 "Screw on the coin slide came lose,Reinstalled test ok..."
Omar S.
WASHER WHIRLPOOL CAE2745FQ0 "Screw on the coin slide came lose,Reinstalled test ok..."
Aris S.
WASHER WHIRLPOOL CAE2743BQ0 "Run unit on service diagnostic, unit is working normal at present time., but if problem continues then need to send the control w10860464 & actuator w11212745"
Stoyan S.
DISHWASHER WHIRLPOOL WDT730PAHZ0 Run dw for 35 min no leaks found Unit works as designed
Aris S.
WASHER MAYTAG MVWX655DW1 Suspensiion rod repair. Run unit on service diagnostic unit is working normal
Aris S.
WSH FRT/LOAD WHIRLPOOL WFW92HEFFU0 "Run unit on the spin mode, unit is working normal, no problem was found, but customer is no happy."
Aris S.
MICRO OVEN TOP WHIRLPOOL CMO WMH31017HZ "Fixed a loose connection by light socket, but custumer need to get a new bulb"
Stoyan S.
RANGE WHIRLPOOL WFG525S0HZ0 Replace broken glass All op ok
Gabino P.
WASHER WHIRLPOOL WTW5000DW2 Found code f8e1 reset control board and check ok.