Need Appliance Repair Service? Have a general question?
We love solving problems! Let us know how we can help by reaching out below.
Local Reviews
for Englewood Cliffs, NJ
Great service
Catherine - Englewood Cliffs, NJ
Efficient, knowledgeable, no hassle scheduling. Call in advance.
Mario
Mario - Englewood Cliffs, NJ
Stoyan S.
DISHWASHER KITCHEN AID KDTM354DSS1 Replace defective cntrl and vent Test unit works as designed
Stoyan S.
DISHWASHER WHIRLPOOL KDTM354DSS1 Unit have electrical error for drain and vent Order new parts; ordrng 1 W10708617 (cntrl-elec) and 1 WPW10469574 (vent)
Stoyan S.
RANGE KICTHEN AID KGRS807SSS00 Tubing gas unable to remove Order new ; ordrng 1 9761071 (tubing-gas) and 1 9761072 (tubing-gas)
Gabino P.
DRYER WHIRLPOOL WGD9620HW Found low temperature increase and reset temperature and check ok.
Stoyan S.
OVEN JENN-AIR JJW3830DS02 Bad console F2E1 error Order new panel ; ordrng 1 W11232121 (CONSOLE )
Aris S.
WASHER WHIRLPOOL GA810 "Unit is making noise, unit have many problems, need the trans, the bearing, the pulley. But many parts are no longer available."
Aris S.
REFRIG/FREEZER WHIRLPOOL GARF19XXPK01 "Found a bad relay, install one, need 24 hours to adjusted.; used 1 W10613606 (OVERLOAD) from stock"
Aris S.
WASHER WHIRLPOOL CAE2745FQ0 Install parts test it is working good
Aris S.
WASHER WHIRLPOOL CAE2745FQ0 "I call up tech line spoke Alex, need parts.; ordrng 1 W11188527 (cntrl-elec) and 1 WPW10491734 (interface)"
Aris S.
WASHER WHIRLPOOL WTW7500GW "Run unit on service diagnostic, unit is working, problem is overloaded. Check error come, but unit is ok"
Lewis G.
DRYER WHIRLPOOL SDG3606AWW Unit is heating properly and drum only spins when empty one suite is put into the dryer the motor does not run please review parts for repair however customer gonna purchase a new unit.....; ordrng 1 56000 (BLOWER WHEEL) and 1 WP2200376 (MOTOR ASSY)
Gabino P.
WASHER WHIRLPOOL WTW7300DW1 2 cct need transmission making noises customer decline repair bill customer trip charge $122.57
Lewis G.
REFRIG/FREEZER WHIRLPOOL RJRS4270C "SR#7726449598....main board # wp67006854 and condensor motor # wp61005323.,..... diagnosing unit and also with tech-support service matters does not have a parts list was able to get a part number from office please review parts for repair 2 man needed 2 count,....to get to the condenser fan this is a built-in unit......; ordrng 1 wp61005323 (CONDENSOR FAN MOTOR) and 1 wp67006854 (MAIN PCB)"
Stoyan S.
MICROWAVE KITCHENAID KOCE507EBS06 Helper completed
Stoyan S.
OVEN JENN-AIR JJW2830DP01 Clock is going fast with 15 min every month Order new console; ordrng 1 W11236888 (CONSOLE )
Stoyan S.
OVEN JENN-AIR JJW2830DP01 Clock is going fast with 15 min every month Order new console; ordrng 1 W11236888 (CONSOLE )
Eric S.
DRYER WHIRLPOOL MGD5700TQ01 Found bad ignitor replaced part unit works ok
Tim S.
DISHWASHER KITCHENAID KDTM354DSS5 Needs electrician no 120 volts . Customer stated kitchen aide was covering everything/ Authorization only for parts/ Not having conflict with customer/ Did not collect/ Job Cmpltd
Eric S.
DRYER MAYTAG MGDB765FW0 Installed parts tested unit it works ok
Eric S.
DRYER MAYTAG MGDB765FW0 Found f2e1 code UI Problem need parts; ordrng 1 W11089306 (FASCIA ASSY) and 1 W11089308 (CONTROL)
Eric S.
DISHWASHER WHIRLPOOL MDB4949SHZ0 Loose water connection. Adjusted connection no more leaks
Stoyan S.
DISHWASHER JENN-AIR JDB9000CWP2 Replace defective pump motor Test it all op ok ; used 1 WPW10605057 (PUMP & MOTOR) from stock
Eric S.
WASHER WHIRLPOOL WTW5800BW0 Installed parts tested unit it works ok
Stoyan S.
DISHWASHER KITCHENAID KDPE334GPS0 Ck DW no problem found Run diagnostics no error codes stored in memory
Stoyan S.
RANGE JENN-AIR JGS1450DP0 Replace defective parts for errors codes Test it all op ok
Stoyan S.
DISHWASHER JENN AIR JDB8200AWP1 Replace defective wheels lower rack all op ok; used 4 W10195416V (
Eric S.
REFRIGERATOR WHIRLPOOL WRX986SIHZ00 Found leds not working need parts; ordrng 3 W11205083 (LED)s and 3 W11239944 (LED )s
Stoyan S.
DISHWASHER JENN-AIR JDB7910AWB Replace broken handle all op ok